Ford Falcon XB Coupe, V8 351 - Check the Mad Max Interceptor History pages for a LOT more detail. Full stepsA quick list of what vehicles were used: (Note: Where a vehicle is linked , there is a sub-page for that specific vehicle). 4.7 out of 5 stars.Keep the drive in the protective anti-static container until ready to install.
![]() ![]() For Old Mad Dog Dvd Drive For New Full StepsA QuickYou'll see some kind of diagram that looks like this:It's not currently set, but you can fairly easily tell from the diagram what you'll need to set it for. If you want to do that you'll just have to make sure that it's plugged into the right part of the cable.Wonder what connects to where on the cable?If you want to make it the master or the slave, you will have to look around the drive to find where the instructions are. A lot of people like to use what is called Cable Select. The master can also be referred to as the "primary" drive with the slave being the "secondary". Drives come defaulted to be ready to be installed in a single drive environment.First of all Master, Slave? What is this? They had to be called something. This allows the cable to select if the drive is master or slave based on the position on the cable. Cable-Select Option (Default) - Use with Ultra ATA cables. And here one thing to note is that it is preferred to have the CD-ROM and other non-hard drive products on the secondary ATA channel. Master with non-ATA compatible drive - Use this if the drive is Master to a CD-ROM, tape drive or other non-ATA drive. Drive is Slave - Use this setting if the drive is an additional drive on the cable and the original drive is set as Master. Master or Single Drive - Use this setting if the drive is the only drive on the ATA interface cable. Best mac laptop for music production and photo editingIf you have an older drive please visit our Technical Library and find your model number for details on jumper configuration.Before you install the new drive make sure you unplug the power connector from the computer. If the limit capacity jumper is installed you will need to use a drive overlay program such as the one installed by Disc Wizard Starter Edition.The figure below depicts the jumper settings for the U-Series and Barracuda ATA drive families (most Seagate ATA drives above 20 GBytes). Limit Capacity Option - This option may be required if the system the drive is being installing into does not support the full capacity of the drive. For that you will have to pull off both side panels to your case. Four if you never touch anything in your system. Two if you're lazy and only screw things in on the side. Just touch the power supply for a precaution OK?Now you should be able to find an open 3.5" slot somewhere.Slide the drive into an available slot and find 2 or 4 case screws. It's also a good idea to touch the power supply before you go sticking your hands in there! Static discharge can jump and do some bad things. This pin always goes on the same side as the power connector.To connect the IDE cable to the motherboard you'll have to find something that looks like this:Each connector represents 1 IDE channel. Normally it's red on the grey cables and white on black cables etc there will be some kind of colored line to indicate pin 1. On the edge of one of the cables you will see a line. If they aren't then you've got some troubleshooting to do. You should be able to see some kind of message on the screen when it first posts indicating what you need to push.Once you're in the BIOS you'll want to go into standard CMOS where you should see something like this:Enable LBA mode and UDMA mode, if applicable.If your drives are showing up properly then you did it right. Generally it's the button that gets you into the BIOS but sometimes it's F1 or F2. ![]() Since most of people are using Windows 2000 or XP, so overleap all the steps in fdisk. You'll need to fdisk this. If your using Windows 9x (why?) then you'll want to check out bootdisk.com and find something that'll cover your needs. If this new drive is going to be your main drive then use the partition application that is built into Windows. Just clicking next until you get here.If you're only using Windows, we would suggest using NTFS. If this is a secondary drive then you're obviously after pure storage space so just make it a primary partition and allocate 100% of your space to it.The followed screen looks like this. Select New Partition.A wizard will pop up and walk you through this process. The disk with all of the unallocated space is what you're after. Go into the Control Panel -> go under Administrative Tools -> Computer Management -> Storage -> Disk Management.Look on the bottom right and you'll see something that looks like this picture. Most modern CD drives are ATA33 while the modern hard drives are ATA133. If you have this backwards the drive will normally either be silent or fail to power up.Is the full capacity of the hard drive being seen:Verify the BIOS has auto-detected and LBA mode is enabled.Make sure you have your CD/DVD drives plugged into a different channel/cable. Pin 1 is almost always the closest to the power connector. You will see some kind of stripe running down the side of the cable that will indicate pin 1. If not, select the auto-detect option.Check to make sure the IDE cable is connected correctly. TroubleshootingDo you have two drives on the cable? Make sure both of the drives aren't set for the same setting (master or slave).Make sure the power is plugged in and everything is connected securely.Verify the drive is enabled in system BIOS.
0 Comments
Leave a Reply. |
AuthorAngie ArchivesCategories |